Trades & DIY

Tile, Adhesive & Grout Estimator

Enter the area and tile size to get tiles, boxes, adhesive bags and grout in one go.

Area
7.20 m²
Tiles needed
44
Boxes to buy
8
Adhesive
32.4 kg · 2 × 20kg bags
Grout
1.6 kg · 1 × 2.5kg bags
Tile cost
£176.00

Measuring the surface and choosing an allowance

Measure the area you intend to tile, not the whole room if cabinets, a bath panel or another finish will cover part of it. A rectangular floor is length × width; a wall is width × tiled height. Split alcoves and irregular shapes into rectangles and add their areas. Keep a sketch with dimensions, door openings and the intended tile direction. An area total is useful for ordering, but it does not establish where the first tile or the perimeter cuts will fall.

The tool calculates tile face area from length and width in millimetres converted to metres. It adds your selected 5%, 10% or 15% allowance, divides by tile face area and rounds up to whole tiles. It then divides by tiles per box and rounds up again. Both steps matter: even if a calculation suggests part of a box, you normally buy a complete carton. Tile cost is based on the resulting box count, not on an unrounded square-metre estimate.

Worked tile and box example

For a 3 m × 2.4 m floor, net area is 7.2 m². A 600 mm × 300 mm tile covers 0.18 m². With 10% waste, required coverage becomes 7.92 m², giving 44 tiles. At six tiles per box, that means eight boxes, containing 48 tiles. The difference between 44 and 48 is pack rounding, not a second percentage allowance. At £22 per box, the tile-only cost is £176. Adhesive, grout, trim, preparation and labour are additional costs.

Grout joints and setting out

Joint width affects the spacing of a finished layout. A 600 mm tile with a 3 mm joint creates an approximately 603 mm repeating module. For a row of N full tiles, the distance between the outside edges is N × tile length + (N − 1) × joint width, before perimeter movement gaps. Use that relationship to check cuts and alignment. Do not simply divide a wall length by tile length and assume every joint will disappear into the available space.

This calculator does not reduce the tile count for the area occupied by grout joints. It uses face area as a straightforward purchasing estimate, while the joint input affects grout consumption. That distinction is especially important for mosaics or very wide joints. Check the actual supplied tile dimensions, recommended joint widths and batch variations before setting out. Nominal dimensions on a product name can differ from the finished size.

Adhesive coverage and trowel choice

The estimating assumption is 1.5 kg of adhesive per m² per millimetre of compressed bed. It assumes the bed compresses to half the selected 3, 6 or 10 mm notch dimension. This gives approximate rates of 2.25, 4.5 and 7.5 kg/m². For the 7.2 m² example with a 6 mm notch, the result is 32.4 kg, rounded to two 20 kg bags. Different trowel shapes, working angles, substrate flatness and adhesive formulations can change consumption substantially.

Large-format tiles may require back-buttering or a different trowel to achieve the manufacturer's required coverage. The tool does not automatically add an extra allowance for back-buttering. Follow the tile and adhesive instructions, lift a recently placed tile to inspect coverage where appropriate, and avoid treating a thin bed as a way to correct a badly uneven floor. Wet areas and heated floors can also require different product specifications and preparation.

Grout estimation

The formula is kilograms = ((L + W) ÷ (L × W)) × tile depth × joint width × 1.6 × area, using millimetres for tile dimensions, depth and joint width. The 1.6 constant is a typical estimating density factor. For 600 × 300 × 9 mm tiles with 3 mm joints over 7.2 m², it gives approximately 1.56 kg of grout, rounded to one 2.5 kg bag. Wider joints or smaller tiles increase the total joint volume and therefore consumption.

The assumed depth is tile thickness; actual joint filling depth and grout formulation may differ. Check the manufacturer's consumption chart for the chosen product, especially for epoxy grout or unusual tile profiles. Avoid mixing a full bag if the product's working time and the job size make smaller batches more practical.

Tiling questions and practical tips

Is 10% or 15% wastage better?

Ten percent is a useful starting allowance for a conventional layout; diagonal patterns, herringbone, many corners or fragile tiles may justify 15% or more. These are planning assumptions, not guaranteed cutting losses. A dry layout or drawing can refine the estimate.

Should I keep spare tiles?

Yes, retaining matching batch tiles can help with later repairs. Check every box before installation for shade, size and damage. Do not rely on a future order matching an old batch exactly.

How the tile calculation works

Tiles: area × (1 + waste %) ÷ tile face area, rounded up, then divided by tiles per box and rounded up again.

Adhesive: a notched trowel leaves ridges that compress to roughly half the notch depth. Most cement-based adhesives use about 1.5 kg per m² per mm of bed, so a 6mm notch uses ~4.5 kg/m².

Grout uses the industry formula kg = (L + W) ÷ (L × W) × tile depth × joint width × 1.6 × area with dimensions in mm and 1.6 as the typical grout density.

Choosing a trowel

Larger tiles need a thicker bed for full coverage. For floor tiles over 300mm, back-butter the tile as well and add around 20% more adhesive. Always check the manufacturer's coverage figures on the bag.

Common UK tile sizes

Tile (mm)Tiles per m²Typical use
100 × 100100.0Splashbacks, mosaics
200 × 10050.0Metro / subway walls
250 × 40010.0Bathroom walls
300 × 30011.1Floors
600 × 3005.6Walls & floors
600 × 6002.8Large floors
1200 × 6001.4Large format