Converters
Metric ↔ Imperial Unit Converter
Pick a category, type a value and see it converted into every other unit instantly.

- Millilitres10,000
- Cubic metres0.01
- UK gallons2.199692
- US gallons2.641721
- UK pints17.59754
- US pints21.133764
- Cubic feet0.353147
Convert the quantity, not just the unit label
A reliable conversion starts by identifying what is being measured. Length, area, volume, mass, pressure and speed have different dimensions and cannot be substituted for one another. The tool assigns every unit in a category a factor relative to a base unit. It multiplies your input by the source factor, then divides by the destination factor. Each equivalent is calculated from the original input rather than from a previously rounded result. Display rounding still applies, so keep adequate precision for your final task.
Many familiar conversions are exact definitions: the international inch is exactly 0.0254 m, the foot is 0.3048 m and the pound is 0.45359237 kg. The litre is exactly 0.001 m³. Squared and cubed units require squared and cubed conversion factors. For example, one square foot is 0.3048² = 0.09290304 m², not 0.3048 m². This distinction prevents large ordering errors when moving from a room dimension to a floor area.
UK Imperial and US Customary volume
A UK Imperial gallon is exactly 4.54609 L. A US liquid gallon is exactly 3.785411784 L. Ten UK gallons therefore equal 45.4609 L, while ten US gallons equal 37.85411784 L. The Imperial gallon is about 20.1% larger than the US liquid gallon; reversing the comparison, the US gallon is about 16.7% smaller. Always state the reference system when quoting a gallon, especially in fuel economy, water tanks and recipes.
Both systems have eight pints to a gallon, but their pints inherit the different gallon sizes. A UK pint is 0.56826125 L and a US liquid pint is 0.473176473 L. Four pints are therefore about 2.273 L in the UK system and 1.893 L in the US system. US dry measures are another convention and should not be confused with the liquid measures used here.
Fluid ounces differ as well: an Imperial pint has 20 Imperial fluid ounces, whereas a US liquid pint has 16 US fluid ounces. An Imperial fluid ounce is 28.4130625 mL; a US fluid ounce is 29.5735295625 mL. Unlike the gallon, the US fluid ounce is the larger of the pair. Fluid ounces measure volume; ordinary ounces measure mass. This converter's volume list includes gallons and pints but not a separate fluid-ounce selector, so the figures here are explanatory references rather than extra output options.
Engineering pressure: bar, PSI, kPa and water head
One bar is exactly 100 kPa or 100,000 Pa. PSI means pounds-force per square inch; one bar is approximately 14.5038 PSI. A 2.4 bar tyre specification is therefore about 34.81 PSI. Check whether an instrument reports gauge pressure relative to atmosphere or absolute pressure: changing units does not change that reference. Never assume a safe working pressure from a numerical conversion alone.
Water head relates pressure to the height of a fluid column using pressure = density × gravity × height. The tool uses the conventional approximation 1 m of water head = 9.80665 kPa = 0.0980665 bar. A 10 m head is therefore about 0.9807 bar. Real water density varies with temperature, and actual installations also lose pressure through friction and fittings. The conversion does not calculate those losses or size a pump.
Speed, mass and practical precision
The speed table converts scalar speed, not direction-dependent velocity vectors. One mph is exactly 1.609344 km/h, so 60 mph is 96.56064 km/h. One knot is one nautical mile per hour, equivalent to 1.852 km/h. Mach depends on local speed of sound; the listed Mach factor assumes sea-level air at 15°C. It is not a universal factor for hot air, high altitude or another medium.
For ingredients, converting millilitres to grams requires density. A litre of flour is not a kilogram simply because a litre of water is approximately one kilogram. Use the recipe scaler's ingredient-specific approximations for culinary conversions. Likewise, a tonnes-to-cubic-metres conversion for aggregate needs a bulk density and cannot be derived from the mass table alone.
Conversion questions
Why do two websites give slightly different results?
They may use different systems, round factors earlier or report fewer decimal places. Check the full unit name and whether a factor is exact or approximate. A rounded display is usually adequate for everyday comparisons but may not be suitable for a tolerance calculation.
How should I record a converted specification?
Keep the original value and unit beside the converted value, including UK or US where relevant. Round only at the final step and match the precision of the original measurement rather than implying accuracy that was never measured.
Sources and further reading
How the conversion works
Every unit in a category is stored as a multiple of one base unit (litres, metres, square metres, kilograms, bar or metres per second). Your value is converted to the base unit, then divided by each target unit's factor: result = value × from factor ÷ to factor. This gives every equivalent at once with no rounding drift between steps.
UK vs US measures
Imperial and US customary units share names but not always sizes. A UK gallon is 4.546 litres while a US gallon is 3.785 litres — about 20% smaller. The same applies to pints (568ml UK vs 473ml US). Always check which system a spec sheet, recipe or fuel figure uses.
Pressure units matter for plumbing and tyres: UK boilers usually show bar (1–1.5 bar cold fill), while tyre pressures are often given in PSI. One metre of water head is roughly 0.098 bar — useful for gravity-fed systems.
Speed and velocity
Speed conversions are all linear, so the same factor method applies: 1 mph is exactly 1.609344 km/h and 1 knot is exactly 1.852 km/h. Road limits in the UK and US are quoted in mph, most of the rest of the world in km/h, and marine and air navigation in knots — one nautical mile per hour. Feet per minute is the usual unit for airflow in ducts and fans, while metres per second is the scientific base unit (sound at sea level on a standard day is about Mach 1, or 340.29 m/s).
Exact reference factors
| Conversion | Exact factor |
|---|---|
| 1 inch | 25.4 mm |
| 1 foot | 0.3048 m |
| 1 mile | 1.609344 km |
| 1 UK gallon | 4.54609 L |
| 1 US gallon | 3.785411784 L |
| 1 pound | 0.45359237 kg |
| 1 stone | 6.35029318 kg |
| 1 acre | 4,046.86 m² |
| 1 bar | 14.5038 psi |
| 1 mph | 1.609344 km/h |
| 1 knot | 1.852 km/h |
| 1 foot/second | 0.3048 m/s |
